InvertaPuls IP 6-2 | 3 x 400 V | Steel/Alu | MB
Please log in to see prices
Available in 20 days, delivery time 2-5 days
Product information "InvertaPuls IP 6-2 | 3 x 400 V | Steel/Alu | MB"
ACT-9041303433-MB
The Inverter MIG-MAG welding machine for body repair with ACT (Automotive Cold Transfer) offers a range of impressive features that make it the ideal choice for vehicle body repair. With two welding torches for two wires, it enables efficient operation while focusing on superior thin sheet welding.
Features
• Synergy parameters
• Lower heat input
• Very good gap bridging
• Less material distortion
• Automatic "hold function" of the welding parameters
• Saving of individual welding programs
• Integrated interface for software updates
Equipped with:
1 x 337220 Wire feed rollers | steel | 0.8 mm & 1.0 mm
1 x 337221 Wire feed rollers | aluminium | 1.0 mm & 1.2 mm
1 x 308110 Torch 3G | Steel welding | 3.0 m
1 x 308111 Torch 3G | ALU welding | 3.0 m
1 x 304053 Ground cable with clamp | 5 m | 35 mm² | SK 35
1 x 311042 Pressure reducer ProControl | 200 bar (GER and AT only)
1 x 311044 Double branch valve 1/4" for manometer (GER and AT only)
1 x operating instructions
| Coating: | powder-coated |
|---|---|
| Content: | 1 stück, 1 piece |
| Current setting range: | 10 - 280 A |
| Effectiveness: | 85 % |
| Frequency: | 50 - 60 Hz (+/- 10 %) |
| Fuse: | 16 A (slow) |
| Length × width × height: | 820 x 430 x 930 mm |
| Mains connection (Cu): | 4 × 2,5 mm² |
| Mains voltage: | 3 ~ 400 V |
| Mark of conformity: | according to 2006/42/EC |
| Material: | Plastic, Steel, kunststoff |
| Open circuit voltage: | 82 V (MIG, TIG), 43 V (MMA) |
| Operating temperature: | -10 bis 40 °C |
| Power factor: | 0,75 |
| Protection class: | IP 23 |
| Sound pressure level: | 66 dB(A) |
| Voltage setting range: | 10 - 50 V |
| Weight: | 62,0 kg |
| Wire diameter: | 0,6 - 1,2 mm |
| Wire speed range: | 0,5 - 22 m/min |
Zubehör
This silicone-free gas nozzle protection paste prevents the rapid clogging of welding torches due to welding spatter on gas and power nozzles.
Please log in to see prices
Trennfix the silicone-free welding protection spray is an extremely efficient separating and lubricating agent. It prevents the rapid clogging of welding torches due to weld spatters on gas and power nozzles.
Please log in to see prices
Aluminum crack testing is used to check for damage in the inner microstructure of the metal.Very often, large areas need to be checked for cracking in order to check whether other body parts have been affected by a crash. A typical example of this is the MacPherson strut area.The diffusion red penetrant is applied to the surface to be tested. Due to its properties and capillary force, it penetrates the finest cracks and pores and is drawn back to the surface after cleaning with the developer. Due to the high contrast to the white developer, even the smallest cracks and defects can be detected.Note: The liquids and agents have no negative properties on welds or on the surfaces on which they are used, they can be easily removed from the surfaces with the test agent cleaner without leaving any residue.Application: 1. Clean the surface thoroughly with cleaner Ardrox 9PR5.2. Apply diffusion red Ardrox 9VF2 and leave to work for approx. 10-20 minutes.3. Thoroughly clean the surface again with cleaner Ardrox 9PR5.4. Apply developer spray Ardrox 9D1B until reaction.5. Check the surface for cracks.
Please log in to see prices
Aluminum crack testing is used to check for damage in the inner microstructure of the metal.Very often, large areas need to be checked for cracking in order to check whether other body parts have been affected by a crash. A typical example of this is the MacPherson strut area.The diffusion red penetrant is applied to the surface to be tested. Due to its properties and capillary force, it penetrates the finest cracks and pores and is drawn back to the surface after cleaning with the developer. Due to the high contrast to the white developer, even the smallest cracks and defects can be detected.Note: The liquids and agents have no negative properties on welds or on the surfaces on which they are used, they can be easily removed from the surfaces with the test agent cleaner without leaving any residue.Application: 1. Clean the surface thoroughly with cleaner Ardrox 9PR5.2. Apply diffusion red Ardrox 9VF2 and leave to work for approx. 10-20 minutes.3. Thoroughly clean the surface again with cleaner Ardrox 9PR5.4. Apply developer spray Ardrox 9D1B until reaction.5. Check the surface for cracks.
Please log in to see prices
Aluminum crack testing is used to check for damage in the inner microstructure of the metal.Very often, large areas need to be checked for cracking in order to check whether other body parts have been affected by a crash. A typical example of this is the MacPherson strut area.The diffusion red penetrant is applied to the surface to be tested. Due to its properties and capillary force, it penetrates the finest cracks and pores and is drawn back to the surface after cleaning with the developer. Due to the high contrast to the white developer, even the smallest cracks and defects can be detected.Note: The liquids and agents have no negative properties on welds or on the surfaces on which they are used, they can be easily removed from the surfaces with the test agent cleaner without leaving any residue.Application: 1. Clean the surface thoroughly with cleaner Ardrox 9PR5.2. Apply diffusion red Ardrox 9VF2 and leave to work for approx. 10-20 minutes.3. Thoroughly clean the surface again with cleaner Ardrox 9PR5.4. Apply developer spray Ardrox 9D1B until reaction.5. Check the surface for cracks.
Please log in to see prices
Compact 13-piece nozzle cleaning needle set in a practical, hinged metal box. Contains approx. 90 mm long needle files (0.4-1.6 mm) and a flat file - ideal for cleaning oxyfuel welding nozzles. Scope of delivery: - 13 needles and 1 flat file- robust blue aluminum box
Please log in to see prices
Special pliers with 4 functions for power nozzles with a diameter of 12 - 15 mm.• Fast and precise trimming of the welding wire• Time-saving cleaning of the shielding gas nozzle• Removal of the shielding gas nozzle• Loosening and tightening of the power nozzle
Please log in to see prices
Temperature indicators are temperature indicating pens with a calibrated melting point. The marking melts when a temperature of 100 °C is reached. It has a accuracy of +/- 1 % of the nominal temperature. For determining the surface temperature at:• Welding and metal fabrication• Preheating• Intermediate storage• Heat treatment after welding• Soft annealing• Stress relief annealingApplication:Mark the workpiece before or during heating. When the nominal temperature is reached, the marking melts (runs) clearly visible. This method is suitable for smooth surfaces.
Please log in to see prices
Temperature indicators are temperature indicating pens with a calibrated melting point. The marking melts when a temperature of 204 °C is reached. It has a accuracy of +/- 1 % of the nominal temperature.For determining the surface temperature at:• Welding and metal fabrication• Preheating• Intermediate storage• Heat treatment after welding• Soft annealing• Stress relief annealingApplication: Mark the workpiece before or during heating. When the nominal temperature is reached, the marking melts (runs) clearly visible. This method is suitable for smooth surfaces.
Please log in to see prices
Temperature indicators are temperature indicating pens with a calibrated melting point. The marking melts when a temperature of 400 °C is reached. It has a accuracy of +/- 1 % of the nominal temperature. For determining the surface temperature at:• Welding and metal fabrication• Preheating• Intermediate storage• Heat treatment after welding• Soft annealing• Stress relief annealingApplication: Mark the workpiece before or during heating. When the nominal temperature is reached, the marking melts (runs) clearly visible. This method is suitable for smooth surfaces.
Please log in to see prices
Temperature indicators are temperature indicating pens with a calibrated melting point. The marking melts when a temperature of 500 °C is reached. It has a accuracy of +/- 1 % of the nominal temperature. For determining the surface temperature at• Welding and metal fabrication• Preheating• Intermediate storage• Heat treatment after welding• Soft annealing• Stress relief annealingApplication:Mark the workpiece before or during heating. When the nominal temperature is reached, the marking melts (runs) clearly visible. This method is suitable for smooth surfaces.
Please log in to see prices
The centring adapter set is used to align the D200 wire coils on the spool mandrel so that the wire can run straight into the wire inlet.
Please log in to see prices
Two-piece adapter with quick-release for K300 basket wire coils.
Please log in to see prices
One-piece adapter for basket wire coils K300 with eight arms and two closing levers.
Please log in to see prices
Wire feed rollers with 37 mm diameter for wire diameters of 0.6 mm and 0.8 mm.
Please log in to see prices
To extend the support for a second gas cylinder. We recommend 10 litre gas cylinders if two cylinders are fitted.Scope of delivery 1 x adapter plate2 x foam spacer4 x ISKA countersunk head screw M8 x 40 mm | burnished4 x M8 nut | self-locking
Please log in to see prices
MIG and MAG torch holder with magnetic foot.
Please log in to see prices