Welding inverter IM 240-Eco | 230 V
Item number:
341288
Product information "Welding inverter IM 240-Eco | 230 V"
The IM 240-Eco welding machine is a compact MIG-MAG welding inverter specially developed for car body repairs. A unique advantage is the excellent MIG soldering characteristic. The very good steel welding characteristics enable all types of repairs to be carried out on vehicles with very good results.
Equipped with:
1 x 337219 Wire feed rollers | steel | 0.6 mm & 0.8mm
1 x 308103 Torch Force 200 | Steel welding | 3.0 m
1 x Ground cable | 4 m
1 x Operating instructions
| Current setting range: | 20 - 200 A |
|---|---|
| Effectiveness: | 85 % |
| Fuse: | 16 A (slow) |
| Length × width × height: | 880 x 400 x 635 mm |
| Mains connection (Cu): | 3 × 2,5 mm² |
| Mains voltage: | 1 ~ 230 V |
| Mark of conformity: | CE |
| Operating temperature: | -10 bis 40 °C |
| Protection class: | IP 23 |
| Sound pressure level: | 67 dB(A) |
| Voltage setting range: | 10 - 35 V |
| Weight: | 32 kg |
| Wire speed range: | 1,5 - 15 m/min |
Zubehör
Variant item
Welding wire CuSi3 | Ø 0.8 mm | D200 | 5 kg
Item no: 311070
The CuSi3 welding wire with a diameter of 0.8 mm is wound on a D200 plastic spool made of copper-silicon alloy and has a low melting point. It is excellent for both TIG and MIG welding (soldering) of galvanized steel sheets in body construction. In this process, the corrosion protection of galvanized surfaces is largely preserved, and usually, preheating of the base material is not required.It is recommended to keep the weld pool not too wide and to pay attention to low heat input. In MIG welding with a short arc/impulse method, as well as in TIG welding, it is advisable to introduce as much weld material as possible.Applicable shielding gases (EN ISO 14175) for TIG: Argon I1, for MIG: Argon I1, I3.
Variant item
Welding wire CuSi3 | Ø 1.0 mm | D200 | 5 kg
Item no: 311071
The CuSi3 welding wire with a diameter of 1.0 mm is wound on a D200 plastic spool made of copper-silicon alloy and has a low melting point. It is excellent for both TIG and MIG welding (soldering) of galvanized steel sheets in body construction. In this process, the corrosion protection of galvanized surfaces is largely preserved, and usually, preheating of the base material is not required.It is recommended to keep the weld pool not too wide and to pay attention to low heat input. In MIG welding with a short arc/impulse method, as well as in TIG welding, it is advisable to introduce as much weld material as possible. Applicable shielding gases (EN ISO 14175) for TIG: Argon I1, for MIG: Argon I1, I3.
Variant item
Welding wire CuAl8 | Ø 0.8 mm | D200 | 5 kg
Item no: 311072
The CuAl8 welding wire with a diameter of 0.8 mm is wound on a D200 plastic spool. It is made of a copper-aluminum alloy and is suitable for both TIG and MIG welding. This wire variant is characterized by its corrosion and seawater resistance, and it also offers good sliding properties. Preheating is only required for large workpieces (approximately 250 °C).The main application areas of this welding wire include copper-aluminum alloys such as aluminum bronze with an aluminum content of 7 - 9 %, as well as copper and copper-zinc alloys (brass). Additionally, it is suitable for overlay welding on unalloyed and low-alloy steels and cast iron.For the first layer of overlay welding on iron materials, pulse arc welding is recommended. In TIG welding, flux should also be used to prevent the formation of oxides.Applicable shielding gases (EN ISO 14175) for TIG/MIG: Argon I1
Variant item
Welding wire CuAl8 | Ø 1.0 mm | D200 | 5 kg
Item no: 311073
The CuAl8 welding wire with a diameter of 1.0 mm is wound on a D200 plastic spool. It is made of a copper-aluminum alloy and is suitable for both TIG and MIG welding. This wire variant is characterized by its corrosion and seawater resistance, and it also offers good sliding properties. Preheating is only required for large workpieces (approximately 250 °C).The main application areas of this welding wire include copper-aluminum alloys such as aluminum bronze with an aluminum content of 7 - 9 %, as well as copper and copper-zinc alloys (brass). Additionally, it is suitable for overlay welding on unalloyed and low-alloy steels and cast iron.For the first layer of overlay welding on iron materials, pulse arc welding is recommended. In TIG welding, flux should also be used to prevent the formation of oxides.Applicable shielding gases (EN ISO 14175) for TIG/MIG: Argon I1
Variant item
Welding wire SG2 Ti vb | Ø 0.8 mm | D200 | 5 kg
Item no: 311074
The welding wire SG2/TIVB with a diameter of 0.8 mm is coated with bronze, providing additional protection against rust. It is wound on a D200 plastic spool and is made of low-alloyed steel, specifically designed for the MAG welding of non-alloyed and low-alloyed steels. This welding wire is particularly suitable for overlaying manufacturing primers, zinc protective coatings, and rusted components. The weld metal produced by this wire is resistant to aging and can be used at operating temperatures ranging from -10 °C to 450 °C.Applicable shielding gases (EN ISO 14175) for MAG welding include CO2 or mixed gases such as M22, M33, M21, M23
Variant item
Welding wire SG2 Ti vb | Ø 1.0 mm | D200 | 5 kg
Item no: 311075
The welding wire SG2/Ti with a diameter of 1.0 mm is coated with bronze, providing additional protection against rust. It is wound on a D200 plastic spool and is made of low-alloyed steel, specifically designed for the MAG welding of non-alloyed and low-alloyed steels. This welding wire is particularly suitable for overlaying manufacturing primers, zinc protective coatings, and rusted components. The weld metal produced by this wire is resistant to aging and can be used at operating temperatures ranging from -10 °C to 450 °C. Applicable shielding gases (EN ISO 14175) for MAG welding include CO2 or mixed gases such as M22, M33, M21, M23.
Variant item
Welding wire Union X96 | Ø 0.8 mm | D200 | 5 kg
Item no: 311087
The welding wire Union X96 with a diameter of 0.8 mm is a high-strength MAG welding wire with Honda approval. With a nominal strength of 980 MPa (142 ksi), it is specifically designed for MAG welding on steel parts with a strength ranging from 590 to 980 MPa. Additionally, this wire is excellent for MAG welding on steel parts with a strength in the range of 270 to 440 MPa. The Union X96 welding wire is also available in a 15 kg K300 coil (item no. 311007)
Variant item
Welding wire CuAl8 | Ø 1.2 mm | K300 | 15 kg
Item no: 311028
The CuAl8 welding wire with a diameter of 1.2 mm is wound on a K300 basket spool. It is made of a copper-aluminum alloy and is suitable for both TIG and MIG welding. This wire variant is characterized by its corrosion and seawater resistance, and it also offers good sliding properties. Preheating is only required for large workpieces (approximately 250 °C).The main application areas of this welding wire include copper-aluminum alloys such as aluminum bronze with an aluminum content of 7 - 9 %, as well as copper and copper-zinc alloys (brass). Additionally, it is suitable for overlay welding on unalloyed and low-alloy steels and cast iron.For the first layer of overlay welding on iron materials, pulse arc welding is recommended. In TIG welding, flux should also be used to prevent the formation of oxides.Applicable shielding gases (EN ISO 14175) for TIG/MIG: Argon I1
Variant item
Welding wire NiMoCr | Ø 0.8 mm | D200 | 5 kg
Item no: 311036
The welding wire NiMoCr with a diameter of 0.8 mm is wound on a D200 plastic spool and is composed of low-alloy steel. It is suitable for MAG welding of quenched and tempered fine-grain structural steels with a yield strength of approximately 700 MPa. The welded material is suitable for use at temperatures ranging from -50 to 350 °C.The mechanical quality values vary depending on the shielding gas used. Optimal weld quality is achieved by using mixed gas M 21 in conjunction with corresponding welding parameters. Welding can be performed in both the short-circuiting and spray arc modes. The preheating temperature depends on the base material. It is crucial to ensure controlled heat input, with the interpass temperature not exceeding 180 °C.Applicable shielding gases (EN ISO 14175) for MAG welding include mixed gases such as M20, M21, M24, M26.
Wire feed rollers | steel | 0.6 mm & 0.8 mm
Item no: 337219
Wire feed rollers with 37 mm diameter for wire diameters of 0.6 mm and 0.8 mm.
Wire feed rollers | steel | 0.8 mm & 1.0 mm
Item no: 337220
Wire feed rollers with 37 mm diameter for wire diameters of 0.8 mm and 1.0 mm.
Variant item
Torch Force 200 | Steel welding | 3.0 m
Item no: 308103
The preconfigured torch for steel welding is equipped with a wire guide spiral and a blue handle.
Welding and work gloves | cow grain leather
Item no: 881036
Durable gloves made from thick, oil- and water-resistant cowhide leather with a textured surface. Padded back for added protection, unlined inside for better grip, and reinforced with 4-fold Kevlar stitching for durability and strength. With a length of 36 cm, these gloves also offer protection for the forearm.Size XL
Automatic welding helmet P850
Item no: 881042
The automatic welding helmet P850 is ideal for those seeking a reliable and aesthetically pleasing product. The helmet features two sensors for automatic darkening and allows for external adjustment of the protection level according to DIN standards. Equipped with True Color Technology, the helmet provides a clear and sharp view, making it easier for the welder to identify objects in the work area and reducing fatigue. Thanks to the external regulation, the welder can effortlessly switch to grinding mode (GRIND) without having to remove the helmet.
Gas flow tester | CO2 + Argon
Item no: 311048
This gas flow meter is used for precise measurement of the flow rate of argon and CO2. It is very accurate and provides precise results for gas volume metering.
Welding protection spray Trennfix | silicone-free
Item no: 311020
Trennfix the silicone-free welding protection spray is an extremely efficient separating and lubricating agent. It prevents the rapid clogging of welding torches due to weld spatters on gas and power nozzles.
Contact tips M6 x 28 mm | 10-piece set
Item no: 307060
Suitable for welding torches MB 15, MB 24, MB 25, MB 26, 3G, Force 155, Force 200. Scope of delivery 2x ALU nozzles | Ø 1.0 mm2x ALU nozzles | Ø 1.2 mm2x Steel/MIG nozzles | Ø 0.8 mm2x Steel/MIG nozzles | Ø 1.0 mm2x Steel/MIG nozzles | Ø 0.6 mm
MIG-MAG torch holder with magnetic foot
Item no: 311043
MIG and MAG torch holder with magnetic foot.
Nozzle cleaning needle set | 13 pcs.
Item no: 311040
Nozzle cleaning needle set for cleaning of oxyacetylene welding nozzles.
Special pliers | Inert gas welding
Item no: 311041
Special pliers with 4 functions for power nozzles with a diameter of 12 - 15 mm.• Fast and precise trimming of the welding wire• Time-saving cleaning of the shielding gas nozzle• Removal of the shielding gas nozzle• Loosening and tightening of the power nozzle
Ground clamp without cable
Item no: 374415
Ground clamp with copper braiding without ground cable. A crucial component in MIG-MAG welding. Only a clean and perfect ground clamp ensures a trouble-free and stable arc.
Centering adapter for wire coil D200
Item no: 307004
The centring adapter set is used to align the D200 wire coils on the spool mandrel so that the wire can run straight into the wire inlet.
Pressure reducer ProControl | 200 bar
Item no: 311042
Pressure reducer for all common applications with technical gases. Manufactured according to the highest safety standards of ISO 2503. The robust rubber protective cap is rear-sealed for optimal all-round protection against damage and contamination. Long lifespan resulting in cost savings for servicing, spare parts, and repairs. Latest Encapsulated Technology for precise and stable control behavior, ensuring a process-secure, simple, and user-friendly operation. Additional product information • Working pressure gauge double scale Argon 5, 32 l/min - red line at 24 l/min - CO2 5, 30 l/min - red line at 23 l/min• Content manometer 0 - 315 / 200 bar - red line at 200 bar
Adapter for basket wire coil K300 | 1 part
Item no: 307002
One-piece adapter for basket wire coils K300 with eight arms and two closing levers.
Adapter for basket wire coil K300 | 2 parts
Item no: 307003
Two-piece adapter with quick-release for K300 basket wire coils.
Welding screen Landskit 2000
Item no: 881220
Mobile welding protection screen with a slat length of 1800 mm for flexible use.
Farriers pincers | Pliers for vehicle bodywork
Item no: 561030
The car body stripper is a special tool that was developed for dismantling work in car body construction. The cutting edges are additionally hardened and have a hardness of approx. 59 HRC. The tool is made from special tool steel, which is forged and oil-hardened. The pliers are black atramentised, while the head is polished.
Hand wire brush 4-row | stainless steel
Item no: 541211
4-row hand wire brush made of stainless steel.
Hand wire brush for fillet welds | INOX
Item no: 541212
Hand wire brush with a wire diameter of 0.35 mm. Thanks to its V-shape, this brush is ideal for cleaning, scrubbing, and rust removal in fillet welds and V-seams.