Trac Tower 550 HYBRID
Item no: 500025
The mobile Trac Tower 550 is held securely on workshop floors by a pneumatic vacuum base plate and is characterised by outstanding traction. Thanks to its mobility and low weight, the towing tower can be positioned quickly and easily next to the vehicle. Thanks to the soft foam rubber seal, the vacuum plate ensures that it is firmly anchored to the floor even on small bumps.The towing height can be adjusted in 15 positions up to a height of 1.65 metres. This allows the Trac Tower to be used for both high applications such as roof pillars and low applications such as door sills.The pulling force can be precisely adjusted via the remote control of the hybrid winch.Scope of delivery 1 x Trac Tower1 x 500024 Electric winch HYBRID1 x 500020 Vacuum plate | vertical tension1 x 500011 Pulling claw for Trac Tower
Trac Tower 550 HYBRID with X-plate
Item no: X500025
The mobile Trac Tower 550 with the innovative X-Plate is held securely on smooth workshop floors by a pneumatic vacuum base plate and is characterised by outstanding traction. Thanks to its mobility and low weight, the towing tower can be positioned quickly and easily next to the vehicle.The X-Plate ensures that it is firmly anchored to the floor to withstand even the most extreme tensile loads. The new vulcanised rubber coating increases abrasion resistance and ensures a longer service life with intensive use.The pulling height can be adjusted in 15 positions up to a height of 1.65 metres. This allows the trac tower to be used for both high applications such as roof pillars and low applications such as door sills.The pulling force can be precisely adjusted via the remote control of the hybrid winch.Scope of delivery 1 x Trac Tower1 x 500024 Electric winch HYBRID1 x 500018 Vacuum plate X-Plate1 x 500011 Pulling claw for Trac Tower
I-Ductor 4.0 induction device
Item no: 842110
The I-Ductor 4.0 is a versatile induction heating device that has been specially developed for numerous applications in the automotive industry. It is ideal for the precise removal and processing of a wide range of materials and components. For example, the device can be used to remove rear and side windows or glass roofs. The I-Ductor 4.0 also makes it much easier to remove molded parts and adhesives without leaving any residue. The device also enables the removal of sealing materials, sound insulation, tar films and structural adhesives - ideal for repairs and adjustments in the vehicle sector.Scope of delivery 1 x Control unit incl. foot switch 1 x Inductor for windows 1 x Inductor for bolts 1 x Heating glove for surfaces 2 x Plastic wedge | red 1 x Operating instructions
Line Puller Set 1250 | Full set
Item no: 821102
The 1250 mm long Line Puller is used to repair extensive damages and align optical edges over long distances. Despite its length, the Line Puller can be easily operated by a single person. Thanks to the integrated measuring spring, it is possible to reliably measure the height of the sheet metal or edge from the undamaged side of the vehicle. Scope of delivery 1 x Aluminium bar | 1250 mm | with straight feet1 x 821107 Pulling hook with 3 claws | Line Puller1 x 821108 Pulling hook with 3 claws | Line Puller1 x 821142 Pull rod | Ø 8 mm | 4-piece set2 x Suction cup holders1 x Measuring spring bar
Work Station WS 60 | 400 V
Item no: 352060
The Work Station WS60 is a mobile dent repair workstation for automotive body repairs. With features such as heating and welding functions, it offers versatility. The clear display and separate adjustment of time and power enable precise and user-friendly operation, leading to efficient and high-quality repairs.Package includes1x WS 60 transformer1x trolley1x single sided gun1x quick pulling hammer1x accessory tray10x wavy wire
Trac Tower 550 with vacuum plate
Item no: 500001
The mobile Trac Tower 550 is held securely on workshop floors by a pneumatic vacuum base plate and is characterised by outstanding traction. Thanks to its mobility and low weight, the towing tower can be positioned quickly and easily next to the vehicle. Thanks to the soft foam rubber seal, the vacuum plate ensures that it is firmly anchored to the floor even on small bumps.The towing height can be adjusted in 15 positions up to a height of 1.65 metres. This allows the Trac Tower to be used for both high applications such as roof pillars and low applications such as door sills.The pulling force can be controlled precisely and efficiently via a belt-driven manual hoist. Scope of delivery 1 x Trac Tower1 x Ratchet with pulling belt1 x 500020 Vacuum plate | vertical tension1 x 500011 Pulling claw for Trac Tower
Trac Tower 550 with X-Plate
Item no: X500001
The mobile Trac Tower 550 with the innovative X-Plate is held securely on smooth workshop floors by a pneumatic vacuum base plate and is characterised by outstanding traction. Thanks to its mobility and low weight, the towing tower can be positioned quickly and easily next to the vehicle.The X-Plate ensures that it is firmly anchored to the floor to withstand even the most extreme tensile loads. The new vulcanised rubber coating increases abrasion resistance and ensures a longer service life with intensive use.The pulling height can be adjusted in 15 positions up to a height of 1.65 metres. This allows the trac tower to be used for both high applications such as roof pillars and low applications such as door sills.The pulling force can be controlled precisely and efficiently via a belt-driven manual hoist.Scope of delivery 1 x Trac Tower1 x Ratchet with pulling belt1 x 500018 Vacuum plate X-Plate1 x 500011 Pulling claw for Trac Tower
Electric winch HYBRID
Item no: 500024
Hybrid winch with high-precision remote control for the Trac Tower 550.
Propan burner set incl. wooden Box
Item no: 802001
The complete set with all important and necessary accessories including pressure regulator for small and large gas cylinders. Scope of delivery 1 x Hook1 x Wooden case1 x Open-end wrench SW 17/191 x 808001 Torch handle1 x 808003 Pointed burner | curved1 x 808005 Cyclone burner | curved1 x 808004 Hot air burner | curved1 x 808020 Gas bottle 20001 x 808021 Quick connect valve for gas bottle1 x 808027 Refill adapter | DIN-Combi1 x 808028 Excess flow cut-off valve | 2 bars1 x 808023 Pressure regulator | DIN-Combi × R3/8" li1 x 808022 Pressure regulator | R3/8" li1 x 808025 High pressure hose | DIN 4812
Cartridge gun for Betaforce 2850
Item no: 831120
for Betaforce 2850LATTENTION: special order! Item excluded from exchange !!
Cartridge preheater | 2 cartridges
Item no: 831113
The cartridge heating device is designed for two cartridges and offers a continuously adjustable temperature range from 20 °C to 160 °C with a control accuracy of ±1 °C. It features a digital display for target temperature and heating status, with a temperature sensor positioned in the upper section between the two tubes, enabling precise temperature regulation across the entire cartridge. With a heating capacity of 200 W, made in Germany, and CE-certified, the device meets the highest quality standards.
Acetylene torch | complete set
Item no: 802020
Scope of delivery - Welding and cutting device- Pressure regulator | Oxygen- Pressure regulator | Acetylene- Usage site template | Fuel gas- Usage site template | O2- Hose assembly | 10 m
ElectraFlow cartridge gun | battery-operated
Item no: 831105
The ElectraFlow cartridge gun with battery drive allows for easy processing of cartridges and foil bags. It is perfect for precise bead application of 1K adhesives and sealants, ensuring efficient bonding for a variety of applications.
Transformer Multiphase | AP 95 | 230/400 V
Item no: 353007
The transformer multiphase serves as the power source for the Airpuller AP95 dent repair system. It is flexibly adjustable to the local power supply: Reconnectable Single-phase 220 - 240 V, Three-phase 400 V.Note: The transformer is factory-set for the 400 V three-phase power grid.
Handpuller | complete set
Item no: 351010
The hand puller set has been specifically designed for automotive bodywork restoration and repair. It is particularly suitable for minor to moderate repair tasks on steel car bodies with welding lugs. The set is adjustable and facilitates both steel repairs using welding electrodes and aluminum repairs with single and multiple pull claws.
Hot air gun Leister Electron ST 3400 | 230 V
Item no: 801201
Powerful, with improved ergonomics and therefore increased working comfort. Existing nozzles can still be used. The hot air temperature is infinitely adjustable. The air filters integrated in the handle can be easily removed and cleaned. The appliance is equipped with an automatic carbon cut-out (collector protection) and heating element protection.A transport box is included in the scope of delivery.
Crimping pliers | 5-piece set
Item no: 561010
Scope of delivery 1 x 561015 Crimping pliers | no. 1 | narrow/short1 x 561016 Crimping pliers | no. 2 | wide/short1 x 561017 Crimping pliers | no. 3 | wide/long1 x 561018 Crimping pliers | no. 4 | 90° bent1 x 561019 Crimping pliers | no. 5 | rebate opener
Punching and flanging pliers | pneumatic | Ø 5 mm
Item no: 561090
The 5 mm diameter pneumatic punching and setting pliers have been specially developed for processing sheet metal parts on cars, lorries, buses and special vehicles. It is particularly suitable for processing sheet metal cladding and is suitable for sheet thicknesses of up to 1.2 mm for steel and 2.0 mm for aluminium. The pliers enable quick and precise processing of sheet metal parts and are an indispensable tool for body builders and garages.
Telescopic measuring rod | 950 - 3260 mm
Item no: 871004
The Auto-Messfix offers an ideal solution for damage assessment, measuring structural damage, and dimensional control after straightening. The special measuring tips allow measurements even in hard-to-reach areas and between non-flat points. The included measuring cone facilitates determining borehole distances. Knurled screws on the holders of the measuring tubes prevent unintentional adjustment of the tubes. Scope of delivery 2 x 871008 Measuring cone for Auto-Messfix2 x 874020 Measuring tip | short | straight2 x 874021 Measuring tip | short | angled2 x 874026 Measuring tube | long2 x 874027 Measuring tube holder
AirFlow cartridge gun | pneumatic
Item no: 831103
The pneumatic AirFlow cartridge gun is ideal for the use of foil pouches and cartridges. With its bead dispensing mechanism, it enables precise and even application of 1K adhesives and sealants. Thanks to the rod mechanism driven by a piston, it prevents compressed air from entering the sealant.
Crimping pliers | 3-piece set
Item no: 561020
Scope of delivery1 x 561015 Crimping pliers | no. 1 | narrow/short1 x 561016 Crimping pliers | no. 2 | wide/short1 x 561017 Crimping pliers | no. 3 | wide/long
Telescopic measuring rod | 920 - 2610 mm
Item no: 871001
The Auto-Messfix offers an ideal solution for damage assessment, measuring structural damage, and dimensional control after straightening. The special measuring tips allow measurements even in hard-to-reach areas and between non-flat points. The included measuring cone facilitates determining borehole distances. Knurled screws on the holders of the measuring tubes prevent unintentional adjustment of the tubes. Scope of delivery 2 x 871008 Measuring cone for Auto-Messfix2 x 874020 Measuring tip | short | straight2 x 874021 Measuring tip | short | angled2 x 874026 Measuring tube | long2 x 874027 Measuring tube holder
Variant item
Slide hammer incl. double hook | 9 kg
Item no: 511301
This sliding hammer with double hooks is indispensable for any bodyshop. It is ideal for a precise or powerful drive of attachments. The handle is not screwed on but cast. The integrated hand protection is extra-large to prevent potential hand injuries from squeezing.
Slide hammer incl. adapter & Bi-Puller
Item no: 502002
Slide hammer including adapter and bi-puller. The perfect set for pulling and straightening with wiggle wire.
Slot punch | oval hole 6 x 20 mm
Item no: 561002
Pliers for punching a oval hole of 6 × 20 mm. Quick and easy handling for preparing many MIG soldering jobs on body parts. Double hole no longer required. For "steel 37" type sheet metal. Up to max. 1.5 mm sheet thickness.
Slot punch | oval hole 8 x 20 mm
Item no: 561003
Pliers for punching a slotted hole of 8 × 20 mm. Quick and easy handling for preparing many MIG soldering jobs on body parts. Double hole no longer required. For "steel 37" type sheet metal. Up to max. 1.5 mm sheet thickness.
Fix-Cut 2 Scraper set
Item no: 584036
The universal Fix-Cut 2 scraper set is suitable for removing PU adhesive, adhesives, and sealants under the most demanding conditions. The scraper blades are made of knife steel and are extremely sharp. The compact handle with finger protection pad provides special comfort. The blades offer applications for both left and right, and a grinding stone is included in the set for re-sharpening. Scope of delivery 1 x 702520 Handle for Fix-Cut 21 x 702504 Scraper blade | 40 mm | grinding angle 22°1 x 702502 Scraper blade | 20 mm | grinding angle 22° | right1 x 702503 Scraper blade | 20 mm | grinding angle 22° | left1 x 702500 Scraper blade | 16 mm | grinding angle 22° | right1 x 702501 Scraper blade | 16 mm | grinding angle 22° | left1 x 702505 Scraper blade | 16 mm | grinding angle 17°1 x 702506 Scraper blade | 20 mm | grinding angle 17°1 x 702507 Scraper blade | 12 mm | grinding angle 17°1 x 547037 Bench stone | silicon carbide1 x Transport case
Vacuum plate | vertical tension
Item no: 500020
Thanks to the soft foam rubber seal, the vacuum plate ensures that it is firmly anchored to the floor even on small bumps.
Vacuum plate X-Plate
Item no: 500018
The X-Plate ensures that it is firmly anchored to the floor to withstand even the most extreme tensile loads. The new vulcanised rubber coating increases abrasion resistance and ensures a longer service life with intensive use.
Telescopic measuring rod | 415 - 925 mm
Item no: 871002
The Auto-Messfix offers an ideal solution for damage assessment, measuring structural damage, and dimensional control after straightening. The special measuring tips allow measurements even in hard-to-reach areas and between non-flat points. The included measuring cone facilitates determining borehole distances. Knurled screws on the holders of the measuring tubes prevent unintentional adjustment of the tubes. Scope of delivery 2 x 871008 Measuring cone for Auto-Messfix2 x 874020 Measuring tip | short | straight2 x 874021 Measuring tip | short | angled2 x 874026 Measuring tube | long2 x 874027 Measuring tube holder
Repair kit for plastics
Item no: 391300
For the professional repair of typical plastic damages on bumpers, plastic fenders and more.Product informationHot Air Gun: Precision digitally controlled. Electronically regulated, digital temperature adjustment via joystick from 80 – 650 °C, temperature display in 10 °C increments on LCD display. Airflow control in 2 stages from 150 – 500 l/min.• Optimized device balance• Non-slip base• 2-stage blower• LCD info display and programs• Easy temperature adjustment via joystick• Residual heat indicator• Warning for heat accumulation• Hanging option• Replaceable power cordIncluded items1 x Professional hot air gun LCD, 230V, HG2320E1 x 394010 Welding nozzle for hot air gun1 x 394012 Heat protection disc for hot air gun1 x 394014 Reduction nozzle for hot air gun | Ø 9 mm5 x Stainless wteel wire mesh10 x Special plastic welding rods
Hot Stapler | Car plastic repair kit
Item no: 821110
The professional repair solution for bumpers, headlights, and all other plastic parts. Scope of delivery 1 x Hot Stapler control unit including handle1 x 821117 Special pliers HS20 x Repair clip | U shape | 0.6 mm20 x Repair clip | U shape | 0.8 mm20 x Repair clip | V shape | 0.8 mm20 x Repair clip | W shape | 0.6 mm20 x Repair clip | W shape | 0.8 mm
Welding gun PSP 60 | incl. control line | 2 m
Item no: 351070
The welding gun is suitable for the Work Station WS 20, WS 60 and the Transformer AP 95. It comes with a control cable. This gun can be used to weld pins, bolts, washers, and wiggle wire. It is also suitable for sheet metal embossing and working with carbon electrodes.
WS Tinning set
Item no: 812005
The complete set for tinning. Scope of delivery 1 x 801100 Power Jet with cyclone burner1 x 808020 Gas bottle 20001 x 808027 Refill adapter | DIN-Combi1 x 811002 Solder paddle | oiled | round1 x 811003 Solder paddle | oiled | narrow1 x 811004 Solder paddle | oiled | wide1 x 817003 Tin paste Sn97Cu3 | lead free | 1 kg1 x 817010 Tin bars | 25 % lead | 1 kg
Multi-slide hammer
Item no: 351080
Allows for quick dent removal with the triple-layered sheet and additionally provides the option to weld wave wire. Expandable through additional contact pieces for welding: • U-washers • T-pins • Bolts Included items 1 x Contact piece for wave wire 1 x Triple-layered sheet
Powerlift | incl. electrode holder AP 95
Item no: 351050
The Power Lift, including electrode holder, is an ideal addition to the proven Airpuller AP95 dent removal system, enabling efficient removal of deep and large body dents and dings. Experience outstanding performance and precision with this innovative accessory.Application1. The Power Lift can be easily secured without the use of tools.2. Fully depress the power button of the AP95, hang the Power Lift in the AP95 cage, and then release the power button.3. Weld the Power Lift electrodes (included) in place, pull up the lever, and twist off the electrode.4. The Power Lift provides ample space to eliminate sheet metal tensions simultaneously with the dent removal hammer.5. Always support the Power Lift on sheet metal edges or at the edge!6. After removing the Power Lift, any remaining dents in the sheet metal can easily be removed with the Airpuller AP95.
Maxilift | incl. 3-finger Dent Pulling Claw
Item no: 351060
The Maxilift incl. a 3-finger dent pulling claw is the ultimate alignment tool for bodywork repairs. With its unique 3-finger dent pulling claw, it functions as the panel beater's third hand, perfect for pulling up wave wire during dent removal. Robust, precise, and compact – an indispensable companion for any bodyshop.
Double clamp | Jaw width: 33 & 70 mm
Item no: 511315
Double clamp with a narrow and a wide jaw. The advantage: Depending on the requirements, the object can be gripped with either the narrow or the wide side. The clamping screws are offset, allowing thin sheets to be securely held well within the healthy range. The hexagonal heads of the clamping screws are recessed in the clamp body, thereby locked, enabling genuine one-handed clamping.
LED Dent Removal Lamp | suction base
Item no: 388042LED
LED dent removal lamp with suction base. Three precision lines on the impact-resistant protective glass ensure rapid detection of any dent on the vehicle body. Professional repairs can be carried out reliably and without loss of time. The dent removal lamp is equipped with modern light high-frequency technology, guaranteeing increased light output.• LED Flexband 24 V DC light output approx. 800 lm, 6500 K (cool white)• LED Flexband 24 V DC light output approx. 400 lm, 2700 K (warm white)• Reduced glare effect due to prismatic design
K214 Pulling clamp | laterally self-clamping
Item no: 511424
Laterally self-clamping pulling clamp K214.
LED Dent Removal Lamp | magnetic base
Item no: 388040LED
LED dent removal lamp with magnetic base. Three precision lines on the impact-resistant protective glass ensure rapid detection of any dent on the vehicle body. Professional repairs can be carried out reliably and without loss of time. The dent removal lamp is equipped with modern light high-frequency technology, guaranteeing increased light output.• LED Flexband 24 V DC light output approx. 800 lm, 6500 K (cool white)• LED Flexband 24 V DC light output approx. 400 lm, 2700 K (warm white)• Reduced glare effect due to prismatic design
Trolley for Work Station WS 60
Item no: 352062
The trolley for the Work Station WS 60 is made of sturdy sheet steel and features a high-quality powder coating.
Corner pull clamp with double hook adapter | 90°
Item no: 511311
The 90°C angular corner pull clamp with double hook adapter provides automatic self-tightening via the cone and is particularly suitable for applications where conventional clamps are too large or in corners where direct pulling is required for optimal results. The hexagonal clamping screw is recessed in the clamp body, locking it and allowing for easy single-handed clamping. For connection with slide hammers or chains, the double hook 511310 is used. The double hook adapter of the clamp is positioned between the two claws of the hook.